iDecorating
Flooring
Ryobi CCK18082N 18V 8 Piece Kit
£199.99
This 18V kit features all the key tools from the Ryobi One+ range and is fully compatible with all Ryobi Blue and Green tools, batteries and chargers. It comes with 2 x 1.5Ah Ni-Cd batteries, 1-hour Charger and canvas carry case. Features: Circular Saw Ideal for Laminate Flooring; Worktops & Sheet Material; Drill Driver for Fast Driving into Wood; Combi Drill for Drilling Holes in Masonry; Brick & Concrete; Corner Sander Ideal for Sanding in Tight Corners & Awkward Places; Jigsaw for Curved Cutting in Laminate Flooring; Worktops & Sheet Material; Random Orbital Sander for Fast Material Removal on Wood; Plaster; Paint & Metal; Site Radio with FM Receiver & MP3 Input; Battery Tester to Check the Charge of Your Batteries; 2 Year Warranty. Specifications: Combi Drill: Max torque: 34Nm. Impact rate: 0-18,200bpm. Weight 1.6kg. Circular Saw: Blade dia. 150mm x 10mm bore. Bevel cuts 0-45. Weight 2.5kg. Drill Driver: Max. drilling capacity in wood 32mm, steel 10mm. Max. torque 16Nm. Weight 1.1kg. Hammer Drill Driver: Max. drilling capacity in wood 32mm, masonry 13mm, steel 13mm. Impact rate: 5,980 / 20,930bpm. Max torque: 60Nm. Weight 2.2kg. Jigsaw: Max. cut in wood 40mm. Stroke length: 19mm. Weight 2.2kg. Corner Sander: Sanding paper size: 140 x 100mm. Sanding speed: 11,000opm. Orbit diameter 1.8mm. Weight 0.83kg. Random Orbit Sander: Sanding pad size: 125mm. Orbit diameter 1.6mm. Weight 1.28kg. Radio: Speaker output: 3W. Speaker dia: 50mm. Frequency: 87.5-108fm MHz. Weight: 0.52kg. Battery tester suitable for all ONE+ Ni-Cd or Li-ion batteries.
Draper 3 in 1 Wet & Dry Shampoo Vacuum Cleaner 20 Litre Tank 1200w 240v
£194.95
This 3 in 1 vacuum cleaner features a spray extraction facility for valeting carpets, floors, upholstery and even hard surfaces such as tiles and laminate flooring. The detergent is supplied diluted with water in the form of a pressurized spray on to...
Metabo KGS 216 Sliding Mitre Saw 240 Volt 216mm
£173.59
The KGS 216 is a sliding mitre saw designed for the woodworking enthusiast as well as the semi-professional. It is a well designed, well thought through machine that offers tremendous value. With precision bearings on the support rails the KGS216 will give clean, smooth cuts up to an impressive 305mm in width and 65mm in depth. As with the KS216 is comes supplied with an impressive array of standard equipment that you will normally have to pay for. These include strong cast aluminium table with left and right side extension rails inc length stops, work clamp, mains powered line laser, inbuilt work lamp and high adjustable rear fences. Ideal for laminate floor work, cutting 50 x 75mm outdoor decking, floor boards etc.
5003 3 Socket Intermittent Transformer 5 kVA
£148.32
Primarily for use when using portable electric tools on outdoor sites.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVAManufacture to BSEN 61558 - Thermal overload protection - Glass reinforced polyester (GRP) case providing ingress protection to IP44 - Output sockets to BSEN 60309 / IEC 60309 (Previously BS4343) - 2 meter input mains lead2 x 16 Amp outlets 1 x 32 Amp outletIntermittent transformer This item shipped without an input plug. Maximum input current 23A. These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes 'ON' 15 minutes 'OFF'. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVA Portable Tool Transformer - Safety Instructions 1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time. 4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth. 2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again. 5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV. 3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this. 6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.
Edma Straticut Laminate Flooring Guillotine
£137.15
Laminate/MDF flooring guillotine. Cuts neatly without tearing the laminate layer.No breathable dust. Noise free. Does not need sharpening. Maximum cutting width: 210mm. Maximum cutting thickness: 10mm. T...
SIP 18V Cordless Nailer
£99.95
Suitable for trade and DIY use - Ideally used for panelling, tongue and groove, laminate flooring, coving, skirting, picture frames and repairing fences, general jobs around the home etc.
Festool Laminate Special Saw Blade 160x2 2x20 TF48
£96.84
For work on laminate flooring and mineral materials.Specifications:Diameter - 160 mmCutting width - 2.2 mmHole Ø - 20 mmNo. of teeth - 48Chip angle - 4 °Tooth shape - TF...
Authentic Plank Effect Vinyl Flooring Mocha
£79.03
Special high definition design with deep registered emboss for maximum wood looks. 2.5mm suitable for heavy domestic and heavy commercial use. Wider and longer planks for enhanced optics. PU coated for easy maintenance. Stick direct to the sub floor. Features: PU Coated; Realistic Wood Effect; Easy to Clean & Maintain; Easy Adhesive System; 15 Year Domestic / 8 Year Commercial Warranty. Specifications: 3.37sq m per pack. EN 649.
2250/2 Twin Outlet Transformer 2.25 kVA
£64.79
Primarily for use when using portable electric tools on outdoor sites.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVATool Rating 2.25KVA.Output Sockets. 2 x 16amp. Transformer Specifications Input 240 volts 50Hz single phase. Complete with 2 metres of 3-core flexible cable to BS6500 for connection to mains supply and a 13 amp plug.Output 110 volts. Centre tapped and earth screen between primary and secondary windings which is bonded to the centre tap of the secondary winding, the earth pin on each output socket and earth core of the mains input plugs and sockets.BS4343 flush type sockets with spring flap covers fitted as standard. Units are protected by suitably rated thermal overload cut-outs. Portable Tool Transformer - Safety Instructions 1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time. 4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth. 2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again. 5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV. 3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this. 6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.
1500/2 Twin Outlet Transformer 1.50 kVA CM1500
£63.35
Primarily for use when using portable electric tools on outdoor sites.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVATool Rating 1.50 KVA.Output Sockets. 2 x 16amp. Transformer Specifications Input 240 volts 50Hz single phase. Complete with 2 metres of 3-core flexible cable to BS6500 for connection to mains supply and a 13 amp plug.Output 110 volts. Centre tapped and earth screen between primary and secondary windings which is bonded to the centre tap of the secondary winding, the earth pin on each output socket and earth core of the mains input plugs and sockets.BS4343 flush type sockets with spring flap covers fitted as standard. Units are protected by suitably rated thermal overload cut-outs. Portable Tool Transformer - Safety Instructions 1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time. 4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth. 2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again. 5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV. 3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this. 6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.
3300/2 Twin Outlet Transformer 3.3 Kva
£59.03
Primarily for use when using portable electric tools on outdoor sites.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVAPrimarily for use when using portable electric tools on outdoor sites.Tool Rating 3300 VA.Output Sockets. 2 x 16amp.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes 'ON' 15 minutes 'OFF'. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVATransformer SpecificationsInput 240 volts 50Hz single phase. Complete with 2 metres of 3-core flexible cable to BS6500 for connection to mains supply and a 13 amp plug.Output 110 volts. Centre tapped and earth screen between primary and secondary windings which is bonded to the centre tap of the secondary winding, the earth pin on each output socket and earth core of the mains input plugs and sockets.BS4343 flush type sockets with spring flap covers fitted as standard. Units are protected by suitably rated thermal overload cut-outs. Portable Tool Transformer - Safety Instructions 1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time. 4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth. 2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again. 5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV. 3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this. 6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.
1000/2 Twin Outlet Transformer 1000 kVA CM1000
£57.59
Primarily for use when using portable electric tools on outdoor sites.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVATool Rating 1000KVA.Output Sockets. 2 x 16amp.Transformer SpecificationsInput 240 volts 50Hz single phase. Complete with 2 metres of 3-core flexible cable to BS6500 for connection to mains supply and a 13 amp plug.Output 110 volts. Centre tapped and earth screen between primary and secondary windings which is bonded to the centre tap of the secondary winding, the earth pin on each output socket and earth core of the mains input plugs and sockets.BS4343 flush type sockets with spring flap covers fitted as standard. Units are protected by suitably rated thermal overload cut-outs. Portable Tool Transformer - Safety Instructions 1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time. 4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth. 2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again. 5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV. 3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this. 6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.
Wiss M-12R Red Handled´Supershear´
£55.64
WISS Metalmaster Supershear for the cutting of autopanels, sheet metal, vinyl floor tiles, heating and ventilation ducting, printed circuit boards etc, and stainless steel up to 0.8mmSize 11inRed Handles....
7501 Single Outlet Transformer 750 kVA
£54.71
Primarily for use when using portable electric tools on outdoor sites.- Manufactured to BS3535 - Thermal overload protection - BS4343 output sockets as standard - Glass reinforced polyester case - Input flex and 13 amp plug - Transformer completely encapsulated for extra weatherproofing These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVATool Rating 750KVA.Output Sockets. 1 x 16amp. Transformer Specifications Input 240 volts 50Hz single phase. Complete with 2 metres of 3-core flexible cable to BS6500 for connection to mains supply and a 13 amp plug.Output 110 volts. Centre tapped and earth screen between primary and secondary windings which is bonded to the centre tap of the secondary winding, the earth pin on each output socket and earth core of the mains input plugs and sockets.BS4343 flush type sockets with spring flap covers fitted as standard. Units are protected by suitably rated thermal overload cut-outs. Portable Tool Transformer - Safety Instructions 1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time. 4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth. 2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again. 5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV. 3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this. 6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.
Wiss M-11R Black Handled´Supershear´
£51.59
WISS Metalmaster Supershears for the cutting of autopanels, sheet metal, vinyl floor tiles, heating and ventilation ducting, printed circuit boards etc.With automatic chip breaker fpr comprehansive cutting out and cutting in.Size 11in...
Wiss M-10R Standard Cutter
£48.88
WISS Metalmaster Shears for the cutting of autopanels, sheet metal, vinyl floor tiles, heating and ventilation ducting, printed circuit boards etc.Size 10in...
M-11R Black Handled Supershear
£42.73
WISS Metalmaster Supershears for the cutting of autopanels, sheet metal, vinyl floor tiles, heating and ventilation ducting, printed circuit boards etc.With automatic chip breaker fpr comprehansive cutting out and cutting in.Size 11in
BevelLOC Rustic White Oak Effect Narrow Plank
£42.22
Suitable for underfloor heating, V' groove planks, Glue-free fitting system
